Please call (800) 624-1866 for a shipping quote. This is the first tandem axle trailer that has given me problems like this. Econoline Trailers' Patented Extra Steady 20,000 pound Multi-Max Trailer Suspension Set. If you replace your current equalizer with one. For example, if you were to go with an equalizer that is one inch taller, you could keep the center hanger the same but would need one inch longer end hangers. Ideal weight distribution of hitch weight is 20 to 25 to the trailer axles, another 20 to 25 to the front axle of the tow vehicle (TV), leaving 50 to 60. When changing the size of the equalizer that is on a trailer, this will affect the size of hangers needed or the spacing of the hangers. The angle of the ball to the coupler affects weight distribution. I'm about to haul it 1400 miles and need to get the trailer up to it. The article is generally true, but for your exact setup you need to go by the setup instructions for your exact WD hitch. It pulls well, but I've only taken to the lake and back once. With the boat on the trailer, it is fairly balanced with probably 300-400 lbs on the tongue. Has anyone seen this before? Is there a reason the distances would be different? Center to center from the front hanger to the equalizer pivot bolt is 29.5". ![]() I took some measurements and the distance on the hangers is off. You would not use just one set on one axle of a triple axle trailer because it would create a poor ride on the trailer and could increase the stress on the other suspension parts. The boat and trailer sat for years so I'm not ignoring the fact that the springs probably need to be replaced. For a triple axle trailer you will need either K71-657-00 with 7-3/4 inch long equalizers or K71-656-00 with 5-5/8 inch equalizers. Although I wouldnt be able to give you the specs for what should be on a Grand Design (thats something only the manufacturer can tell you) I can tell you hangers which fit 1-3/4' leaf springs have an inner width that is close to 1-3/4' such as 115917 which has a 1-13/16' inner width. I think boat comes in around the 5,500 lb mark. The leading edge of the equalizer is only about an 1" off the ground with the boat on it. With the boat on the trailer the suspension is the same. The H248 comes with a set of taller center hangers. The only way to get 6 of these exact hangers is to order a quantity of 6 of them. If you were not going to use the one that came with it. The thickness of the steel of the Hanger part 28-5 is 3/16 of an inch thick. I'll post to let you know how I made out.I have a problematic tandem axle trailer. Expert Reply: Since Equalizer specifically recommends a hitch ball at or less than 2-3/8 inches in length with a 1-1/4 inch diameter shank you would want to use the part 63018 for a 2 inch ball or part 63019 for a 2-5/16 inch hitch ball with the part EQ37100ET. Plan B is to raise the front of the trailer and bounce it a few times. Ask The Experts a Question > Products Referenced in This Question. The rear schackles are straight up and down ( the one with the tires off the ground) and the front straight across, so if I just flip the rears (with my new Johnson Bar) I should be good to go. This kit is designed for smaller trailers like what you have and includes 3-1/8 inch long shackle straps like the TRS元13. If there is a dash-mounted air intake restriction. So tomorrow i'll go to one of the brand new Lowes they built near me and purchase the Johnson Bar (5' was $19) and try to reverse the shackles again. On vehicles with a manual trans- mission, a variety of switches are installed here. and the line was down one the isles and no resolution in site, I put the bar down and left the store without the bar as did most of the people behind me. THE EQUALIZER is a reimagining of the classic series starring Queen Latifah as Robyn McCall, an enigmatic woman with a mysterious background who uses her ext. ![]() I finally decided after 25 years to go get a decent Johnson Bar, went to home depot (they actually have a nice supply and variety) went to the counter (only one open) and some lady was arguing about with the cashier about a $2.00 roll of wallpaper that I was willing to pay for just to get her out of the line, but she said it was principle because it was on the sale rack and didn't ring up for the sale amount. The height of your equalizer is measured from the center of the horizontal mounting holes, to the center of the upper mounting hole as shown as the 2' measurement in the included diagram of the TREQ104. I tried to reverse the shackles with a bar i had and it wasn't long enough.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |